Mechanical, industrial and manufacturing technologies : selected, peer reviewed papers from the 2012 3rd International Conference on Mechanical, Industrial and Manufacturing Technologies (MIMT 2012), March 24-25, 2012, Shenzhen, China / / edited by Li Kai
(Visualizza in formato marc)
(Visualizza in BIBFRAME)
| Titolo: |
Mechanical, industrial and manufacturing technologies : selected, peer reviewed papers from the 2012 3rd International Conference on Mechanical, Industrial and Manufacturing Technologies (MIMT 2012), March 24-25, 2012, Shenzhen, China / / edited by Li Kai
|
| Pubblicazione: | Durnten-Zurich, Switzerland : , : Trans Tech Publications Ltd, , [2012] |
| ©2012 | |
| Descrizione fisica: | 1 online resource (336 p.) |
| Disciplina: | 620.1 |
| Soggetto topico: | Technology |
| Mechanical engineering | |
| Production engineering | |
| Industrial engineering | |
| Manufacturing processes | |
| Soggetto genere / forma: | Electronic books. |
| Altri autori: |
KaiLi
|
| Note generali: | Description based upon print version of record. |
| Nota di bibliografia: | Includes bibliographical references and indexes. |
| Nota di contenuto: | Mechanical, Industrial and Manufacturing Technologies; Preface and Committees; Table of Contents; Chapter 1: Research in Numerical Simulation and Optimisation; Numerical Simulation on Shock Initiation of Double-Shell Charges by High Velocity Impact; Research on Simulation System of Aero-Generator; Real-Time Attitude Simulation of Aerocraft Using dSPACE Emulator and Three-Axis Turn Table; Electric Vehicle Transmission Gear Ratio Optimization Based on Particle Swarm Optimization; Numerical Simulation Research on the Hydrodynamic Forces Acting on a Tanker in Oblique Motion |
| Study on the Efficiency Optimization of U-Shaped Curve Rail Type AS/RSChapter 2: Characteristic Studies of Mechanical and Material Systems; Study on Sheet Bonding and Break Strength Characteristics; Static and Dynamic Stiffness Characteristics Analysis of Hydro-Pneumatic Suspension; Evaluation of Tensile Properties of Pressure Vessel Materials by Shear Punch Test Method; Analysis of the Dynamic Response of a Cracked Beam Structure; Visualization of Supersonic Non-Newtonian Liquid Jets | |
| Deformation and Stresses Analysis in FG Rotating Hollow Disk and Cylinder Subjected to Thermal and Mechanical LoadTest and Numerical Analysis of Underwater Explosion on Circular Plates; Comparing of the Welding Atmosphere Moisture Effect on Hydrogen Distribution in TI-6AL-4V, Pure Commercial Titanium and TI-15V-3CR-3SN-3AL Weld Joints; Chapter 3: Chaotic States and Analysis of Systems; Design and Research of Electric Vehicle Driving System Based on SOPC; Study on the Temperature Filed of Wet Dual Clutch Transmission during Starting Process | |
| Research on Taylor Vortices in the Wedge-Shaped Air Gap of Evaporation Cooling Turbo GeneratorOmni-Vision System of Intelligent Car Based on DSP & FPGA; Finite-Time Chaos Control and Synchronization of the New Chaotic System with Unknown Parameters; Chaotic Analysis of the Velocity Signal in Impinging Stream Mixer; Modeling and Experiment on Active Vibration Control of Hydraulic Excitation System; The Study of Ball and Plate System Based on Non-Linear PID; Finite Element Analysis of the Static/Dynamic Behavior of Wind Turbine Gearbox | |
| Design of Auto Route Identified Vehicle Model Based on MC9S12XS128Finite Element Analysis of Flextensional Transducer with Slotted Shell; Chapter 4: Vibrational Analysis and Mechanics of Structures etc.; Experimental Study on Bending Capacity of Plain Wall System; Gear Vibration Monitoring System Based on Virtual Instruments; Design and Dynamic Walking Control of Humanoid Robot SCUT-I; Maximum Bending Moment and Maximum Additional Bending Moment for High Vertical Vessels under Wind Pressure; Experimental Research on Trajectory Control of Walking Rehabilitation Training Robot | |
| Kinematics Simulation and Control System Design of Serial Robot Based on ADAMS and Pro/E | |
| Sommario/riassunto: | These proceedings consist of the fully refereed papers presented at the conference. The main conference themes were Mechanical Engineering, Materials and Energy. The peer-reviewed papers are divided into six chapters: Research in Numerical Simulation and Optimisation; Characteristic Studies of Mechanical and Material Systems; Chaotic States and Analysis of Systems; Vibrational Analysis and Mechanics of Structures etc.; Materials Science and Technologies; Mechanical/Automotive Systems and Allied Topics. |
| Titolo autorizzato: | Mechanical, industrial and manufacturing technologies |
| ISBN: | 3-03813-854-1 |
| Formato: | Materiale a stampa  |
| Livello bibliografico | Monografia |
| Lingua di pubblicazione: | Inglese |
| Record Nr.: | 9910462784803321 |
| Lo trovi qui: | Univ. Federico II |
| Opac: | Controlla la disponibilità qui |
Serie:
Applied mechanics and materials ; ; v. 187.