Innovative materials : engineering and applications : selected, peer reviewed papers from the International Conference on Material Engineering and Applications, (ICMEA 2014), October 18-19, 2014, Hangzhou, China / / edited by Anil K. Bhatnagar
(Visualizza in formato marc)
(Visualizza in BIBFRAME)
| Titolo: |
Innovative materials : engineering and applications : selected, peer reviewed papers from the International Conference on Material Engineering and Applications, (ICMEA 2014), October 18-19, 2014, Hangzhou, China / / edited by Anil K. Bhatnagar
|
| Pubblicazione: | Pfaffikon, Switzerland : , : Trans Tech Publications Ltd, , 2014 |
| ©2014 | |
| Descrizione fisica: | 1 online resource (595 p.) |
| Disciplina: | 620.11 |
| Soggetto topico: | Materials |
| Materials science | |
| Soggetto genere / forma: | Electronic books. |
| Persona (resp. second.): | BhatnagarAnil K <1942-> (Anil Kumar) |
| Note generali: | Description based upon print version of record. |
| Nota di bibliografia: | Includes bibliographical references at the end of each chapters and indexes. |
| Nota di contenuto: | Innovative Materials: Engineering and Applications; Preface and Committees; Table of Contents; Chapter 1: Composites, Materials Engineering and Technologies; The Micro-Analysis about the Morphology and Characteristics of the Ball Mill Slag Powder; The Research of Hydrophilic Modification of PVC/PES Blended Membrane by the Additive of CA; High Speed Extrusion Rheological Behavior Analysis of Marine ABS/PC Alloy; First-Principle Studies on the Stability of AlN(0001)/NbB2(0001) Interface |
| Mechanical Properties and Toughening Mechanisms of Multi-Walled Carbon Nanotube Reinforced Yttria-Stabilized Zirconia Composite Energetic Studies on the B Effect on the Oxidation of γ-TiAl Alloys; Carbon Fiber Reinforced SiC Matrix Composites Fabricated by Preceramic Impregnation and Pyrolysis Process Combining SiC Nano Powder Infiltration; Fabrication of TiB2/TiC Duplex Particles Reinforced Carbon Steel Matrix Surface Composite; Static Recrystallization and Texture Evolution of 316L Stainless Steel Fibers; Research in an Original Si-Mn-Mo-Nb 800MPa Dual Phase Steel with Low Carbon | |
| Effect of Copper Content on Mechanical Properties of Short Carbon Fiber Reinforced ZrC Mateix Composites Study on the Brush Plating Technology of Super-Strength Duralumin; Polyurethane Nanocomposite Films by Using Cellulose Nanospheres as Green Nanofillers; Performance Improvement of Hydrogen Peroxide Sensor via Cadmium Doped Nickel Oxide Modifying N-Silicon Electrode; A Novel Method for Co-Simulating 1-3 Piezocomposite Performance; Different Carbon Nanotube Content and Dispersant on the Preparation of Fe3O4 / CNTs; Three-Dimensional Simulation of Nano-Composite Ceramic Tool Materials | |
| Temperature Influences on Preparation and Tribological Characteristics of Electrostatically Sprayed PTFE/PEEK Composite Coatings Study on Preventing Springback for Nanoporous Thermal Insulating Composites; The Preparation and Research of the Electroless Plating Rare Earth Alloys; Two-Step Annealing for Solution-Based Metal Induced Crystallization of Amorphous Silicon Films; Influence of WC Content on Microstructure and Wear Resistance of (Cu-50Mo)-WC Composites; Effect of TiC Content on the Microstructure and Wear Resistance of (Cu/50W)-TiC Composite Prepared by Spark Plasma Sintering | |
| Chapter 2: Functional Materials The Study of Electromagnetic Steel Sheet High Cycle Fatigue Properties; Stiffness and Damping Characteristics of a Wide Parabolic Film Slider Bearing Operating with Ferrofluids; Temperature Influence on the Viscoelastic Electromechanical Deformation of Dielectric Elastomer; Dielectric Strength of Flame-Retardant Reinforced Polyamides at High Temperature; A 1D Analysis of Nano Multiferroic Composites for the Novel Read Head Technology | |
| First-Principle Study on Half-Metallic Ferromagnetism and Structural Stability of C-Doped Alkaline-Earth Chalcogenides under Pressure | |
| Sommario/riassunto: | Collection of selected, peer reviewed papers from the 2014 International Conference on Material Engineering and Application, October 18-19, 2014, Hangzhou, China. The 100 papers are grouped as follows: Chapter 1: Composites, Materials Engineering and Technologies, Chapter 2: Functional Materials, Chapter 3: Luminescent and Optical Materials, Chapter 4: Polymer Materials Science, Chapter 5: Bio and Medical Materials Engineering, Applications, Chapter 6: Building and Constructions Materials, Applications, Chapter 7: Measurement, Detection and Test Procedures, Chapter 8: Materials Processing and |
| Titolo autorizzato: | Innovative materials |
| ISBN: | 3-03826-702-3 |
| Formato: | Materiale a stampa  |
| Livello bibliografico | Monografia |
| Lingua di pubblicazione: | Inglese |
| Record Nr.: | 9910459969303321 |
| Lo trovi qui: | Univ. Federico II |
| Opac: | Controlla la disponibilità qui |
Serie:
Advanced materials research ; ; Volume 1052.