| |
|
|
|
|
|
|
|
|
1. |
Record Nr. |
UNINA9910459969303321 |
|
|
Titolo |
Innovative materials : engineering and applications : selected, peer reviewed papers from the International Conference on Material Engineering and Applications, (ICMEA 2014), October 18-19, 2014, Hangzhou, China / / edited by Anil K. Bhatnagar |
|
|
|
|
|
|
|
Pubbl/distr/stampa |
|
|
Pfaffikon, Switzerland : , : Trans Tech Publications Ltd, , 2014 |
|
©2014 |
|
|
|
|
|
|
|
|
|
ISBN |
|
|
|
|
|
|
Descrizione fisica |
|
1 online resource (595 p.) |
|
|
|
|
|
|
Collana |
|
Advanced Materials Research, , 1662-8985 ; ; Volume 1052 |
|
|
|
|
|
|
Disciplina |
|
|
|
|
|
|
Soggetti |
|
Materials |
Materials science |
Electronic books. |
|
|
|
|
|
|
|
|
Lingua di pubblicazione |
|
|
|
|
|
|
Formato |
Materiale a stampa |
|
|
|
|
|
Livello bibliografico |
Monografia |
|
|
|
|
|
Note generali |
|
Description based upon print version of record. |
|
|
|
|
|
|
Nota di bibliografia |
|
Includes bibliographical references at the end of each chapters and indexes. |
|
|
|
|
|
|
|
|
Nota di contenuto |
|
Innovative Materials: Engineering and Applications; Preface and Committees; Table of Contents; Chapter 1: Composites, Materials Engineering and Technologies; The Micro-Analysis about the Morphology and Characteristics of the Ball Mill Slag Powder; The Research of Hydrophilic Modification of PVC/PES Blended Membrane by the Additive of CA; High Speed Extrusion Rheological Behavior Analysis of Marine ABS/PC Alloy; First-Principle Studies on the Stability of AlN(0001)/NbB2(0001) Interface |
Mechanical Properties and Toughening Mechanisms of Multi-Walled Carbon Nanotube Reinforced Yttria-Stabilized Zirconia Composite Energetic Studies on the B Effect on the Oxidation of γ-TiAl Alloys; Carbon Fiber Reinforced SiC Matrix Composites Fabricated by Preceramic Impregnation and Pyrolysis Process Combining SiC Nano Powder Infiltration; Fabrication of TiB2/TiC Duplex Particles Reinforced Carbon Steel Matrix Surface Composite; Static Recrystallization and Texture Evolution of 316L Stainless Steel Fibers; Research in an Original Si-Mn-Mo-Nb 800MPa Dual Phase Steel with Low Carbon |
Effect of Copper Content on Mechanical Properties of Short Carbon |
|
|
|
|
|
|
|
|
|
|
|
Fiber Reinforced ZrC Mateix Composites Study on the Brush Plating Technology of Super-Strength Duralumin; Polyurethane Nanocomposite Films by Using Cellulose Nanospheres as Green Nanofillers; Performance Improvement of Hydrogen Peroxide Sensor via Cadmium Doped Nickel Oxide Modifying N-Silicon Electrode; A Novel Method for Co-Simulating 1-3 Piezocomposite Performance; Different Carbon Nanotube Content and Dispersant on the Preparation of Fe3O4 / CNTs; Three-Dimensional Simulation of Nano-Composite Ceramic Tool Materials |
Temperature Influences on Preparation and Tribological Characteristics of Electrostatically Sprayed PTFE/PEEK Composite Coatings Study on Preventing Springback for Nanoporous Thermal Insulating Composites; The Preparation and Research of the Electroless Plating Rare Earth Alloys; Two-Step Annealing for Solution-Based Metal Induced Crystallization of Amorphous Silicon Films; Influence of WC Content on Microstructure and Wear Resistance of (Cu-50Mo)-WC Composites; Effect of TiC Content on the Microstructure and Wear Resistance of (Cu/50W)-TiC Composite Prepared by Spark Plasma Sintering |
Chapter 2: Functional Materials The Study of Electromagnetic Steel Sheet High Cycle Fatigue Properties; Stiffness and Damping Characteristics of a Wide Parabolic Film Slider Bearing Operating with Ferrofluids; Temperature Influence on the Viscoelastic Electromechanical Deformation of Dielectric Elastomer; Dielectric Strength of Flame-Retardant Reinforced Polyamides at High Temperature; A 1D Analysis of Nano Multiferroic Composites for the Novel Read Head Technology |
First-Principle Study on Half-Metallic Ferromagnetism and Structural Stability of C-Doped Alkaline-Earth Chalcogenides under Pressure |
|
|
|
|
|
|
Sommario/riassunto |
|
Collection of selected, peer reviewed papers from the 2014 International Conference on Material Engineering and Application, October 18-19, 2014, Hangzhou, China. The 100 papers are grouped as follows: Chapter 1: Composites, Materials Engineering and Technologies, Chapter 2: Functional Materials, Chapter 3: Luminescent and Optical Materials, Chapter 4: Polymer Materials Science, Chapter 5: Bio and Medical Materials Engineering, Applications, Chapter 6: Building and Constructions Materials, Applications, Chapter 7: Measurement, Detection and Test Procedures, Chapter 8: Materials Processing and |
|
|
|
|
|
|
|
| |