Info
- Utilizzare la checkbox di selezione a fianco di ciascun documento per attivare le funzionalità di stampa, invio email, download nei formati disponibili del (i) record.
Design and Control of Power Converters 2019
| Design and Control of Power Converters 2019 |
| Autore | de Azpeitia Manuel Arias Pérez |
| Pubbl/distr/stampa | Basel, Switzerland, : MDPI - Multidisciplinary Digital Publishing Institute, 2021 |
| Descrizione fisica | 1 online resource (402 p.) |
| Soggetto topico | Technology: general issues |
| Soggetto non controllato |
AC/AC converter
active clamp adaptive hysteresis current control binary particle swarm optimization (BPSO) buck converter bus converter cascaded H-bridge (CHB) circulating current coil design current-mode control DC bus DC-AC converter DC-DC converter dc-link voltage balance control decoupling design space differential flatness digital control distributed power generation system (DPGS) DPWM dSPACE semi-physical verification experimental verification feedback loop control frequency domain fuzzy fuzzy identification fuzzy model predictive control fuzzy modeling gain crossover frequency GaN-based inverter and converter global best solution grid-connected voltage source converters (GC-VSCs) half-bridge current-source converters harmonic injection HIL Testbed hybrid storage systems hybrid systems hysteresis control inductive power transfer Inductor-Capacitor-Diode Inductor-Diode inversion formulae LED driver light emitting diode (LED) linear active disturbance rejection control linear extended state observer low frequency oscillation magnetics design matrix converter MMC model-based predictive current control (MBPCC) modelling MPPT multilevel converter networked power converters nonisolated nonlinear control nonsingular terminal sliding mode control (NTSMC) optimal gain Pareto optimality peak to average ratio (PTAR) PFC converters phase margin photovoltaic power system PLC power control power converters power efficiency power electronic converter power electronic converters power factor correction proportional integral proportional resonant pulsating output current PV-connected inverter reactive power resources reduced order generalized integrator (ROGI) reliability single-phase system sliding-mode control SPPT step-down supercapacitors supervisory controller switched affine systems switching converters synchronous rectification three-port converter total harmonic distortion (THD) traction line-side converter (LSC) two degrees of freedom two-stage buck converter vehicle-grid coupling system virtual damping voltage regulation wireless power transfer zeta inverter |
| Formato | Materiale a stampa  |
| Livello bibliografico | Monografia |
| Lingua di pubblicazione | eng |
| Record Nr. | UNINA-9910557743103321 |
de Azpeitia Manuel Arias Pérez
|
||
| Basel, Switzerland, : MDPI - Multidisciplinary Digital Publishing Institute, 2021 | ||
| Materiale a stampa | ||
| Lo trovi qui: Univ. Federico II | ||
| ||
Design and Management of Manufacturing Systems
| Design and Management of Manufacturing Systems |
| Autore | Gola Arkadiusz |
| Pubbl/distr/stampa | Basel, Switzerland, : MDPI - Multidisciplinary Digital Publishing Institute, 2021 |
| Descrizione fisica | 1 online resource (452 p.) |
| Soggetto topico | Technology: general issues |
| Soggetto non controllato |
3D printing devices
8 disciplines method additive manufacturing additive manufacturing technology advanced industrial engineering assembly-line balancing batch processors car tire production process CFR-PEEK closed-loop green supply chain constraint programming constraint satisfaction problem cost estimation custom cable assemblies customer satisfaction deadlock decision support decision support systems decision trees decision-making process defects dispatching eco-design effectiveness efficiency empirical data distribution empirical research end-of-life treatment entire product lifecycle environmental impact factory of the future failure prediction functional test fused filament fabrication fuzzy logic generalized cell formation government subsidy hard computing approach layout lean maintenance life cycle analysis Life Cycle Assessment logistic regression machine failure machinery manufacturing performance manufacturing systems Markov model methods of optimizing the arrangement of workstations modelling and simulation monitoring of production processes multi-objective optimization multicriteria optimization multilayer network multiple response optimization n/a optimal process parameters p-median problem Petri net polish manufacturing company predictive scheduling process variables product quality production machines production maintenance production planning production planning optimisation production planning optimization production process capability production process design production processes productivity project management questionnaire survey re-manufacturing readiness real-time control reconfigurable manufacturing system recycling reengineering robust scheduling rough set theory rubber industry semi-Markov model semiconductor manufacturing simulated annealing simulation siphon smart factory solar power plant stackelberg game supervisory controller system-wide performance unit and small-lot production design for manufacturability wafer fabrication wind power plant |
| Formato | Materiale a stampa |
| Livello bibliografico | Monografia |
| Lingua di pubblicazione | eng |
| Record Nr. | UNINA-9910557502803321 |
|
Gola Arkadiusz
|
||
| Basel, Switzerland, : MDPI - Multidisciplinary Digital Publishing Institute, 2021 | ||
| Materiale a stampa | ||
| Lo trovi qui: Univ. Federico II | ||
| ||