Science and engineering of materials : selected, peer reviewed papers from the 1st International Conference on Science & Engineering of Materials 2013 (ICoSEM 2013), November 13-14, 2013, Kuala Lumpur, Malaysia / / edited by Mohd Rafie Johan and Noorsaiyyidah Darman Singho
(Visualizza in formato marc)
(Visualizza in BIBFRAME)
| Titolo: |
Science and engineering of materials : selected, peer reviewed papers from the 1st International Conference on Science & Engineering of Materials 2013 (ICoSEM 2013), November 13-14, 2013, Kuala Lumpur, Malaysia / / edited by Mohd Rafie Johan and Noorsaiyyidah Darman Singho
|
| Pubblicazione: | Zurich, Switzerland : , : TTP, , 2014 |
| ©2014 | |
| Descrizione fisica: | 1 online resource (331 p.) |
| Disciplina: | 620.11 |
| Soggetto topico: | Materials science |
| Soggetto genere / forma: | Electronic books. |
| Persona (resp. second.): | JohanMohd Rafie |
| SinghoNoorsaiyyidah Darman | |
| Note generali: | Description based upon print version of record. |
| Nota di bibliografia: | Includes bibliographical references at the end of each chapters and indexes. |
| Nota di contenuto: | Science and Engineering of Materials; Preface and Committees; Table of Contents; Chapter 1: Biomaterials; Biomimetic Porosity of Gelatin-Hydroxyapatite Scaffold for Bone Tissue; Removal of Pb (II) by CS2 Modified Kenaf Powder; The Effects of YSZ-Al2O3 Addition on Hydroxyapatite Fabricted by Powder Metallurgy; The Potential of Quercetin in Psidium guajava L. Leaves Extract as Bioinhibitor for Controlled Released Fertilizer; Synthesis and Properties of Biphasic Calcium Phosphate Prepared by Different Methods; Chapter 2: Catalytic Materials |
| Decolorization of Methylene Blue by Photocatalyst in the Ag3PO4-AgI SystemChapter 3: Ceramics; Investigation of Ultrasonic Pretreatment on the Synthesis of Zeolite-T and its CO2 Adsorption Characteristics; Sintering Effects on Microstructure and Electrical Properties of (Na0.5K0.5)0.94Li0.06NbO3 Lead-Free Ceramics; Vapochromic Copper (I) Pyrazolate Complex Materials for Phosphorescent Chemosensors of Ethanol; Chapter 4: Coating and Surface Engineering; A Study on Biocompatibility of Gadolinium Based Anodizing Coating AZ91D Magnesium Alloy in Simulated Body Fluid (SBF) Solution | |
| Characterization of Oxide Film by Vanadium Based Anodic Oxidation CoatingInvestigation of Surface Characteristics of Hydroxyapatite/Titanium Composite Layer Obtained by HF Magnetron Sputtering; Chapter 5: Composites; Basalt Carbon Hybrid Composite for Wind Turbine Rotor Blades: A Short Review; Effect of Maleic Anhydride Grafted Poly(actic acid) on Properties of Sawdust/Poly(lactic acid) Composites Toughened with Poly(butylene adipate-co-terephthalate) | |
| Effects of Sawdust Content and Alkali Treatment on Mechanical and Flame Retarding Properties of Sawdust/Recycled High Density Polyethylene CompositesElectron Beam Crosslinking of EVA/ENR-50/HNTS Nanocomposites in the Presence of Trimethylol Propane Triacrylate, TMPTA; Quasi-Static Flexural and Indentation Behaviour of Polymer-Metal Laminate; Chapter 6: Electronic and Electronic Packaging; Corrosion Behavior of Soldered and Laser-Welded Ni-Free Co-Cr Alloy Joints in Sodium Chloride Solution | |
| Deposition of Amorphous Boron Carbide Films with Pulsed Magnetron Sputtering and Evaluation of their Mechanical PropertiesFabrication and Characterization of RF Magnetron Sputtered Silicon Oxide Films; Fabrication Method of Mems Based Clamped-Clamped Resonant Magnetometer; Humidity Sensors on Thermally Oxidized Silicon Substrates; Influence of Spinning Speed on the Properties of Sol-Gel Spin Coated ZnO Films; Microstructural and Electrical Conductivity of Annealed ZnO Thin Films; Preparation and Mechanical Characterization of Amorphous B-C Films | |
| Relationship between Precursor Gas Flow Rate with the Structural and Morphology Properties of Diamond like Carbon Films | |
| Sommario/riassunto: | Collection of selected, peer reviewed papers from the 1st International Conference on Science & Engineering of Materials 2013 (ICoSEM 2013), November 13-14, 2013, Kuala Lumpur, Malaysia. The 61 papers are grouped as follows: Chapter 1: Biomaterials; Chapter 2: Catalytic Materials; Chapter 3: Ceramics; Chapter 4: Coating and Surface Engineering; Chapter 5: Composites; Chapter 6: Electronic and Electronic Packaging; Chapter 7: Concrete and Structural Materials; Chapter 8: Material Modeling and Simulations; Chapter 9: Environmentally Sustainable Materials and Processing; Chapter 10: Materials Con |
| Titolo autorizzato: | Science and engineering of materials |
| ISBN: | 3-03826-473-3 |
| Formato: | Materiale a stampa  |
| Livello bibliografico | Monografia |
| Lingua di pubblicazione: | Inglese |
| Record Nr.: | 9910464510703321 |
| Lo trovi qui: | Univ. Federico II |
| Opac: | Controlla la disponibilità qui |
Serie:
Advanced materials research ; ; Volume 970.