Vai al contenuto principale della pagina
Autore: |
Raghavendra Gujjala
![]() |
Titolo: |
Recent Advances in Mechanical Engineering, Volume 1 : Select Proceedings of ICMech-REC 23
![]() |
Pubblicazione: | Singapore : , : Springer Singapore Pte. Limited, , 2024 |
©2024 | |
Edizione: | 1st ed. |
Descrizione fisica: | 1 online resource (673 pages) |
Altri autori: |
DeepakB. B. V. L
![]() ![]() |
Nota di contenuto: | Intro -- Contents -- About the Editors -- Vibration Analysis of Composite Viscoelastic Core Sandwich Beam Using Active Control Techniques -- 1 Introduction -- 2 Methodology -- 2.1 Materials Required -- 2.2 Experimental Set-Up -- 2.3 Active Vibration Control -- 3 Results and Discussions -- 3.1 Viscoelastic Sandwich Beams -- 3.2 Active Vibration Control Viscoelastic Core Beams -- 4 Conclusions -- References -- Parametric Optimization for Material Removal Rate During Face Milling: Using Experimental and Mathematical Modelling Approach -- 1 Introduction -- 2 Material and Methods -- 3 Results and Discussion -- 3.1 Experimentation and Validation -- 4 Mathematical Modelling -- 4.1 Empirical Modelling of Material Removal Rate -- 5 Conclusion -- References -- Performance Prediction of Electrode Materials on Surface Roughness During Electric Discharge Machining of HSLA Steel -- 1 Introduction -- 2 Material and Methods -- 2.1 Selection of Tool and Workpiece -- 2.2 Preparation of Tooling and Workpiece -- 2.3 Machining Set-Up and Experimentation -- 3 Results and Discussion -- 3.1 Empirical Expression by Regression Analysis (L8 Array) -- 4 Conclusion -- References -- Effect of Sodium Hydroxide Molarity on the Properties of Metakaolin-Eggshell-Based Geopolymer Cured at Ambient Temperature -- 1 Introduction -- 2 Materials and Methods -- 2.1 Materials -- 2.2 Samples Preparations and Mix Proportioning -- 2.3 Test Methods -- 3 Results and Discussions -- 3.1 Workability -- 3.2 Initial and Final Setting Times -- 3.3 Compressive Strength -- 3.4 Split Tensile Strength -- 3.5 Water Absorption -- 3.6 Abrasion Resistance -- 3.7 Resistance to Sulfuric Acid -- 4 Conclusions -- References -- A Selection of Renewable Energy Using Three-Phase Hybrid Fuzzy Model to Attain Sustainable Development Goals -- 1 Introduction -- 2 The Proposed Three-Phase Hybrid Fuzzy MCDM Model. |
2.1 Hesitant Fuzzy Sets -- 2.2 HFL AHP and TOPSIS -- 3 Methodology Implementation -- 4 Conclusions -- References -- Design and Fabrication of Automated Delivery Drone Using 3D Printing -- 1 Introduction -- 2 Methodology -- 2.1 Phase 1 -- 2.2 Phase 2 -- 2.3 Phase 3 -- 2.4 Phase 4 -- 3 Components -- 3.1 Flight Controller -- 3.2 Electronic Speed Controller -- 3.3 Brushless DC Motors -- 3.4 Propellers -- 3.5 Pixhawk Power Module -- 3.6 Battery -- 3.7 Global Positioning (GPS) -- 3.8 RF Transmitter and Receiver -- 3.9 Telemetry -- 4 Block Diagram of Control System -- 5 Design and Fabrication and Flight-Testing -- 5.1 Designing of Quadcopter Drone Body -- 5.2 Fabrication and Assembly of Quadcopter Drone and Flight-Testing: -- 6 Conclusions and Future -- 6.1 Conclusions -- 6.2 Future Scope -- References -- Numerical Investigation of Fluid Flow and Heat Transfer in Microchannel Heat Sink with Rectangular Grooves and Sine Wavy Channels -- 1 Introduction -- 2 Mathematical Governing Equations -- 3 Numerical Investigation -- 3.1 Geometry and Meshing: -- 3.2 Data Reduction -- 3.3 Grid Independence Test (GIT) -- 3.4 Validation -- 4 Results and Discussions -- 5 Conclusions -- References -- Design and Experimental Analysis of Additively Manufactured Ortho-Planer-Based Tuned Mass Damper -- 1 Introduction -- 2 Experimental Methodology -- 2.1 Design of Tuned Mass Damper -- 2.2 Redesigning of Damper -- 2.3 Tuning According to Parameters -- 2.4 Simulation and Experimental Setup -- 3 Results and Discussions -- 4 Conclusions -- References -- Prediction of Depth of Defect from Phased Array Ultrasonic Testing Data Using Neural Network -- 1 Introduction -- 2 Simulation -- 3 Experiment -- 4 Test Material and Experimental Setup -- 5 Feature Extraction -- 6 Neural Network -- 7 Results -- 8 Discussion and Conclusion -- References. | |
Experimental Investigation and Its Parametric Analysis of AWJM Process Parameters on Surface Quality of Green Composites -- 1 Introduction -- 2 Experimental Set-Up Details -- 3 Results and Discussions -- 3.1 Main Effect of Input Variables on Ra -- 3.2 Mathematical Model for Ra -- 3.3 Confirmatory Tests -- 4 Conclusions -- References -- Investigations to Examine the Potential of Eco-Safe Nanofluids in CNC Machining -- 1 Introduction and Literature Review -- 2 Materials and Methods -- 3 Results and Discussion -- 3.1 Characterization of Nanoparticles -- 3.2 Thermal Conductivity -- 3.3 Absorbance -- 3.4 Cutting Temperatures -- 3.5 Cutting Forces -- 3.6 Surface Roughness -- 3.7 Tool Wear -- 3.8 Chip Morphology -- 4 Conclusions -- References -- Ride Analysis of 6 × 6 Military Mine Protected Vehicle on Cross-Country Terrain with PID Controller -- 1 Introduction -- 2 Mathematical Modelling -- 2.1 Half-Car Model Setup -- 2.2 Equations of Motion -- 2.3 Selecting Optimum Value of Damping Coefficient -- 3 Simulation -- 3.1 Simulink Model -- 3.2 Model Validation -- 3.3 Road Profile Generation -- 4 Results and Discussion -- 4.1 Suspension Model Response for Step Input -- 4.2 Suspension Model Response for Rough Road Profile -- 5 Conclusions -- References -- Experimental Analysis and Multi-objective Optimization for Wedm Machining of Armour Steel -- 1 Introduction -- 2 Experimentation -- 3 Results and Discussion -- 3.1 ANOVA Analysis -- 3.2 Effect of Process Parameters on Performance Characteristics -- 4 Optimization of Wedm Parameters Using Desirability Function Approach -- 5 Conclusions -- References -- Improvement of Microstructure and Mechanical Properties of Powder Coating on Ti-6al-4 v Alloy with Different Rare Earth Metals Using Tig Cladding -- 1 Introduction -- 2 Materials and Method -- 2.1 Selection of the Cladding Technique -- 2.2 Selection of Method. | |
2.3 Experiment Setup -- 2.4 Experimental Procedures -- 2.5 Techniques of Characterization -- 3 Result and Discussion -- 3.1 Coating Morphology -- 3.2 Analysis of Coating Thickness -- 3.3 Microstructure -- 3.4 Microhardness -- 4 Conclusion -- References -- Concentrating Solar Energy for Community Cooking -- 1 Introduction -- 1.1 Solar Radiation in India -- 2 Concentrating Solar Power Technologies -- 2.1 Comparison of CSP Technology to Other Renewable Energy Sources -- 3 Concentrating Solar Power Technologies for Community Cooking -- 3.1 Types of Concentrating Solar Power Technologies for Community Cooking -- 4 Case Studies -- 4.1 CSP Cooking System at New Sai Prasadyala, Shirdi -- 4.2 India One Project, Mount Abu -- 5 Economic Analysis -- 5.1 Economic Analysis of New Sai Prasadyala, Shirdi Kitchen -- 5.2 Economic Analysis of India One Project, Mount Abu -- 6 Conclusions and Future Prospects -- References -- Pin-On-Disk Computational Analysis: A Powerful Tool for Characterizing the Mechanical Properties of Polymers and Polymer Composites -- 1 Introduction -- 2 Materials, Geometry, and Mesh -- 3 Computational Methodology -- 4 Results and Discussions -- 4.1 Results with Free Pin Inner Surface -- 4.2 Results with Fixed Pin Inner Surface -- 5 Conclusions -- References -- Simulation of CI Engine Using 60-Degree Sector Meshed Geometry with Diesel-Methanol/Ethanol Blended Fuel -- 1 Introduction -- 2 Methodology -- 2.1 Mesh Generation -- 2.2 Solver Details -- 2.3 Types of Fuels Employed for CFD Analysis -- 2.4 CFD Settings and Engine Specification -- 2.5 Model Establishment -- 2.6 Model Validation -- 3 Results and Discussion -- 3.1 Thermal Efficiency -- 3.2 Indicated Specific Fuel Consumption (ISFC) -- 3.3 Indicated Power -- 3.4 Indicated Mean Effective Pressure -- 3.5 Spatial-Temporal Simulation Analysis -- 4 Conclusions -- References. | |
Vibration Energy Harvesting from Cantilever Beam Using Macro Fiber Composite Material -- 1 Introduction -- 2 Experimental Setup and Methodology -- 3 Results and Discussion -- 3.1 Comparative Study -- 4 Conclusion -- References -- Modeling and Analysis of Fracture Problems Using Meshless Methods -- 1 Introduction -- 2 Formulation of Fracture Problems -- 2.1 RPIM -- 2.2 EFGM -- 3 A Study on Efficient Approach to Deal with Crack Problems -- 4 Numerical Results -- 5 Conclusions -- References -- Design and Analysis of Free Rotation Forklift Using Mecanum Wheel -- 1 Introduction -- 2 Design and Analysis -- 2.1 Design of Mecanum Drive -- 2.2 CAD Model of Forklift Using Mecanum Wheel -- 2.3 Design Calculations -- 2.4 Structural Analysis -- 3 Results and Discussion -- 3.1 Structural Analysis for Base Frame Using ANSYS -- 3.2 Structural Analysis for Wheel Rim Using ANSYS -- 4 Conclusion -- References -- Tribological Investigation of Composite Coating on AISI 52100 Alloy Steel Using Electrophoretic Deposition -- 1 Introduction -- 2 Materials and Methods -- 2.1 Substrate and Electrolyte Preparation -- 2.2 Electrophoretic Deposition -- 2.3 Microscopic Examination and Heat Treatment of EPD Coating -- 2.4 Tribological Test -- 2.5 Optimization of Composition of TiC & -- GO -- 2.6 Design of Experiment (DOE) -- 3 Results and Discussion -- 3.1 Optimization Study of Different Combinations of TiC and GO -- 3.2 Experimental Results from Pin on Disk Tribometer -- 3.3 Tribological Study of Optimum Coated Sample -- 3.4 Wear Study -- 4 Conclusion -- References -- Performance and Emission Characteristics of Higher Blends of Preheated Pongamia Methyl Ester Using Exhaust Gas Waste Heat Recovery in Compression Ignition Engine -- 1 Introduction -- 2 Materials and Methods -- 2.1 Pongamia Oil Methyl Ester Preparation -- 3 Experimental Setup -- 4 Results and Discussion. | |
4.1 Combustion Analysis. | |
Titolo autorizzato: | Recent Advances in Mechanical Engineering, Volume 1 ![]() |
ISBN: | 981-9709-18-0 |
Formato: | Materiale a stampa ![]() |
Livello bibliografico | Monografia |
Lingua di pubblicazione: | Inglese |
Record Nr.: | 9910847081003321 |
Lo trovi qui: | Univ. Federico II |
Opac: | Controlla la disponibilità qui |