LEADER 10947nam 2200505 450 001 9910627257303321 005 20230307090345.0 010 $a981-19-3866-0 035 $a(MiAaPQ)EBC7105460 035 $a(Au-PeEL)EBL7105460 035 $a(CKB)24978729800041 035 $a(PPN)265858208 035 $a(EXLCZ)9924978729800041 100 $a20230307d2022 uy 0 101 0 $aeng 135 $aurcnu|||||||| 181 $ctxt$2rdacontent 182 $cc$2rdamedia 183 $acr$2rdacarrier 200 00$aAdvances in forming, machining and automation $eselect proceedings of AIMTDR 2021 /$fUday S. Dixit [and three others] 210 1$aSingapore :$cSpringer,$d[2022] 210 4$d©2022 215 $a1 online resource (655 pages) 225 1 $aLecture Notes in Mechanical Engineering 311 08$aPrint version: Dixit, Uday S. Advances in Forming, Machining and Automation Singapore : Springer,c2022 9789811938658 327 $aIntro -- AIMTDR 2021, Conference Core Organizing Committee -- Foreword -- Preface -- Contents -- About the Editors -- Forming -- A Novel Method for Identification of Mechanical Properties During Impact Forming of SS 304L Sheet -- 1 Introduction -- 2 Experimental Methodology -- 2.1 Mechanical Properties of the Material -- 2.2 Shock Tube Experiment -- 2.3 Strain Rate Evolution Measurement -- 3 Results and Discussion -- 3.1 Determination of Rate-Dependent Mechanical Properties -- 4 Conclusions -- References -- An Experimental Study of Forced Cooling in Single-Scan Laser Bending -- 1 Introduction -- 2 Experimental Details -- 3 Results and Discussion -- 4 Conclusion -- References -- Determination of the Flow Stress of Material Based on a Friction-Independent Test on a Simple Geometry -- 1 Introduction -- 2 Proposed Method for Determining the Flow Stress -- 2.1 Optimization Procedure -- 2.2 Details of Experiment -- 3 Results and Discussions -- 4 Conclusions -- References -- Development of Flexible Mechanism for Two-Point Incremental Forming -- 1 Introduction -- 2 Challenges in ISF -- 3 Fixture Design -- 4 Development of Design -- 5 Results and Discussion -- 6 Conclusion -- References -- Effects of Multi-axis Forging on Mechanical and Microstructural Properties of AA6061-T6 Aluminum Alloy -- 1 Introduction -- 2 Experimental Procedure -- 3 Results and Discussion -- 3.1 Compression Test -- 3.2 Microstructural Study -- 3.3 Hardness Study -- 3.4 Approximate Flow Curves -- 3.5 Wear Study -- 4 Conclusion -- References -- Experimental Investigation of Multi-stage Robot-Assisted Single Point Incremental Sheet Forming of Al 6061 Sheet -- 1 Introduction -- 2 Experimental Setup -- 3 Experimental Parameters -- 4 Results and Discussion -- 5 Conclusion -- References. 327 $aFinite Element Prediction of Deep Drawability of Tailor-Welded Blanks Using Non-associated Flow Rule and Anisotropy of Sheet Metal -- 1 Introduction -- 2 Experiments -- 2.1 Material Selection -- 2.2 Fabrication of Tailor-Welded Blanks -- 2.3 Deep Drawing -- 3 Material Modeling Using Non-associative Flow Rule -- 4 Finite Element Modeling -- 5 Results and Discussion -- 5.1 Parameter Identification for the Combined Hardening Model -- 5.2 Prediction of Thinning Profile -- 5.3 Effect of Non-uniform Material Flow on the Cup Edge Profile -- 5.4 Weld Line Movement -- 6 Conclusions -- References -- Investigation on Single-Point Incremental Forming Process of SS316 Sheets at Elevated Temperatures -- 1 Introduction -- 2 Geometry Selection and Feasibility Analysis -- 3 Experimental Setup -- 3.1 Experimental Strategy -- 3.2 Forming of Parts -- 4 Results and Discussion -- 4.1 Forming Limit Diagram -- 4.2 Depth of Failure -- 4.3 Thickness Distribution -- 4.4 Microstructural Study -- 5 Conclusion -- References -- Numerical and Experimental Study on Hydroforming of Thin Metallic Sheets -- 1 Introduction -- 2 Tooling and Experiment -- 2.1 Design of the Die -- 2.2 Fabrication of Die -- 3 Hydroforming Experimental Activity -- 4 Numerical Simulation -- 5 Result and Discussion -- 5.1 Physical Observations at Different Hydroforming Pressures -- 5.2 Elongated Length Versus Pressure -- 5.3 Depth Versus Pressure -- 5.4 Taper Angle Versus Pressure -- 5.5 Upper Fillet Radius and Lower Fillet Radius Versus Pressure -- 5.6 Effect of Strain Rate -- 5.7 Effect of Etching -- 5.8 Experiment with an Alternate Material Sample -- 6 Conclusion -- References -- Porosity of Al-Cu-Ni Alloy with Addition of FeNb Through Sand and Stir Casting Routes -- 1 Introduction -- 2 Experimental Procedure -- 2.1 Manufacturing of AMMCs -- 2.2 Density and Porosity Measurement of AMMCs. 327 $a2.3 Microstructure of AMMCs -- 3 Results and Discussion -- 3.1 Microstructure of AMMCs -- 3.2 Density and Porosity Analysis -- 4 Conclusions -- References -- State-of-the-Art Manufacturing of Metal Foams and Processing-A Review -- 1 Introduction -- 2 Processing Methodologies of Metal Foam -- 2.1 Liquid-State Foaming Methods -- 2.2 Solid-State Foaming Processes -- 2.3 Additive Manufacturing -- 3 Further Processing of Metal Foams for More Practical Manufacturability -- 3.1 Forming of Porous Metals -- 3.2 Joining Methodologies of Metal Foams -- 3.3 Cutting of Metal Foams -- 4 Conclusions -- References -- VIKOR Method-Based Selection of the Most Suited Bioplastic for the Injection Moulding Process Amongst Potential Alternatives -- 1 Introduction -- 2 Properties of Bioplastics (Attributes) Examined for the Selection Process -- 3 Values of the Properties (Attributes) of Bioplastics (Alternatives) -- 4 Bioplastic Selection Using MCDM Method -- 4.1 Criteria Weighting -- 4.2 The VIKOR Method -- 5 Results and Discussion -- 6 Conclusion -- References -- Machining -- 3D Finite Element Simulation of Orthogonal Cutting of Ti-6Al-4V Using Textured Tool -- 1 Introduction -- 2 3D Finite Element Analysis -- 2.1 Material Model -- 2.2 Workpiece/Tool Model -- 3 Results and Discussion -- 4 Conclusion -- References -- A Study on Ultrasonic Vibration and Laser-Assisted Turning of Aluminum Alloy -- 1 Introduction -- 2 Experimental Procedure -- 2.1 Experimental Setup of UVLAT Process -- 2.2 Material and Cutting Tool -- 2.3 Experimental Methodology -- 3 Results and Discussion -- 3.1 Machining Forces -- 3.2 Surface Roughness -- 4 Conclusions -- References -- Advancement of Electrochemical Discharge Machining Process-A Review -- 1 Introduction -- 2 Fundamentals of ECDM -- 2.1 Fishbone Diagram -- 3 Advancement in ECDM -- 3.1 Control of Gas Bubbles and Gas Film. 327 $a3.2 Enhancement of MRR -- 3.3 Improvement of Surface Quality and Dimensional Accuracy -- 3.4 MicroChannel and Milling with Electrochemical Discharge -- 4 Significance -- 5 Summary -- 6 Future Scope -- References -- An Experimental Comparison Study of Dry and Air-Cooled Turning of AISI 1040 Steel -- 1 Introduction -- 2 Experimental Design -- 2.1 Experimental Setup -- 3 Results and Discussion -- 4 Conclusions -- References -- Combined Compromise Solution for Machining Performance Optimization of Modified Polymer Composite -- 1 Introduction -- 2 Materials and Experimentation -- 3 Methodology -- 3.1 Combined Compromise Solution (CoCoSo) -- 4 Result and Discussion -- 5 Confirmatory Test -- 6 Conclusion -- References -- Comparative Study on the Analytical Models for the Workpiece Temperature Distribution During Laser-Assisted Machining -- 1 Introduction -- 2 Analytical Models to Predict the Workpiece Temperature Distribution -- 2.1 Model Proposed by Woo and Cho [16] -- 2.2 Model Proposed by Boo and Cho [17] -- 2.3 Model Proposed by Shang et al. [1] -- 3 Experimental Procedure -- 4 Results and Discussion -- 5 Conclusions -- References -- Development of Aluminium Alloy Thin-Walled Sections by Chemical Milling Process -- 1 Introduction -- 2 Experimental -- 3 Results and Discussion -- 3.1 Masking Agent -- 3.2 Chemical Composition -- 3.3 Microstructure Analysis -- 3.4 Mechanical Properties -- 4 Conclusions -- References -- Effect of Magnetizing Parameters on Surface Integrity During Dry and Cryogenic Grinding of AISI D2 Tool Steel -- 1 Introduction -- 2 Experimentation Procedure -- 3 Results and Discussion -- 3.1 Results -- 3.2 Discussion -- 4 Conclusions -- References -- Effect of Peak Current on Material Removal Rate During EDM of Ti-6Al-4V Using Cold Treated Brass Electrode -- 1 Introduction -- 2 Materials and Methods -- 3 Results and Discussion. 327 $a4 Conclusion and Future Scope -- References -- Emulating Chatter with Process Damping in Turning Using a Hardware-in-the-Loop Simulator -- 1 Introduction -- 2 Mechanical Model of Turning with Process Damping -- 3 Hardware-in-the-Loop Simulator -- 4 Validation of HiL Simulator for a Linear Force Model -- 5 Emulating Stability with Process Damping -- 6 Conclusions -- References -- Experimental and Statistical Analysis of Process Parameters on Micro-milling of Ti-6Al-4V Alloy -- 1 Introduction -- 2 Material and Methods -- 2.1 Design of Experiment (DOE) -- 3 Results and Discussion -- 3.1 Surface Morphology -- 3.2 Statistical Analysis -- 4 Conclusions -- References -- Experimental Investigation on the Cutting Performance of Textured Inserts in Dry Turning of Ti-6Al-4V -- 1 Introduction -- 2 Experimental Details -- 3 Results and Discussion -- 3.1 Textured Inserts Effects on Cutting Forces and Friction -- 3.2 Textured Inserts Effects on Cutting Tool Temperature -- 3.3 Textured Inserts Effects on Cutting Tool Wear -- 4 Conclusions -- References -- Experimental Investigations on Tool Path Strategies in Ball-End Milling -- 1 Introduction -- 2 Experimental Details -- 3 Result and Discussion -- 3.1 Analysis of Surface Roughness -- 3.2 Analysis of Cutting Forces -- 3.3 Analysis of Machining Time -- 4 Grey Relation Analysis -- 5 Conclusion -- References -- Experimental Study on Surface Integrity of Single-Crystal Nickel-Based Superalloy Under Various Machining Processes -- 1 Introduction -- 2 Experimental Setup -- 2.1 Work Material -- 2.2 Specimen Preparation -- 2.3 Machining Experiments -- 2.4 Characterization Techniques -- 3 Results and Discussions -- 3.1 Surface Roughness -- 3.2 White-Layer Thickness -- 3.3 Recrystallization Depth -- 3.4 Crystal Orientation Direction -- 3.5 Misorientation Angle -- 3.6 Machining Affected Zone -- 3.7 Surface Hardness. 327 $a4 Conclusions. 410 0$aLecture notes in mechanical engineering. 606 $aMachining$xAutomation 606 $aMachining$xCosts 615 0$aMachining$xAutomation. 615 0$aMachining$xCosts. 676 $a621.902 702 $aDixit$b Uday S. 801 0$bMiAaPQ 801 1$bMiAaPQ 801 2$bMiAaPQ 906 $aBOOK 912 $a9910627257303321 996 $aAdvances in Forming, Machining and Automation$91732532 997 $aUNINA