LEADER 05535nam 2200649 450 001 9910460561803321 005 20200909225244.0 010 $a3-03826-817-8 035 $a(CKB)3710000000387720 035 $a(EBL)2008458 035 $a(SSID)ssj0001550156 035 $a(PQKBManifestationID)16161730 035 $a(PQKBTitleCode)TC0001550156 035 $a(PQKBWorkID)14807085 035 $a(PQKB)11348724 035 $a(MiAaPQ)EBC2008458 035 $a(Au-PeEL)EBL2008458 035 $a(CaPaEBR)ebr11042419 035 $a(OCoLC)908100886 035 $a(EXLCZ)993710000000387720 100 $a20150425h20152015 uy 0 101 0 $aeng 135 $aurcnu|||||||| 181 $ctxt 182 $cc 183 $acr 200 10$aAdvances in materials and materials processing V $eselected, peer reviewed papers from the 2014 5th International Conference on Advances in Materials and Manufacturing (ICAMMP 2014), December 20-21, 2014, Fuzhou, China /$fedited by Zhengyi Jiang and Xianghua Liu 210 1$aPfa?ffikon, Switzerland :$cTrans Tech Publications Ltd,$d2015. 210 4$dİ2015 215 $a1 online resource (966 p.) 225 1 $aAdvanced Materials Research,$x1662-8985 ;$vVolume 1095 300 $aDescription based upon print version of record. 311 $a3-03835-431-7 320 $aIncludes bibliographical references at the end of each chapters and indexes. 327 $aAdvances in Materials and Materials Processing V; Preface and Committee; Table of Contents; Chapter 1: Composites; Analysis of the Geometry and Microcracks of Kevlar/Epoxy Composites; Effect of Diamond Shape on Surface Roughness of Diamond/Cu Composites; Effect of Diamond Shape on Thermal-Physical Properties of Diamond/Cu Composites; Effects of Sintering Temperature on Microstructure and Wear Properties of Al2O3 Particle Reinforced Al Composites; Preparation of Nickel-Based Al2O3-TiB2 Composite Ceramic Powder 327 $aThe Influence of Sintering Temperature and Whisker Content on the Flexural Strength of Aluminum Borate Whisker Reinforced Aluminum Phosphate Composite Materials The Study of Composite Material of Al-C System; Chapter 2: Low-Dimensional and Nano-Materials; Atomistic Simulation on Buckling Behavior of Monolayer Graphene; Modeling and Simulation for Current-Illumination Characteristics of Carbon Nanotube; Preparation and Thermal Fatigue Behaviors of Silicon Nitride Nano-Ceramics; Study on Dispersion and Rheology of Particles in Water-Based Nano TiN Fluid 327 $aTransmission Performance of Water-Based Nano Fluid Based on Computational Fluid Dynamics?-Cyclodextrin Modified Hybrid Magnetic Nanoparticles as an Adsorbent for Phenol Removal; The Preparation of ZrO2 and the Influence of the Calcination Temperature; The Synthesis of Single-Crystal BiOI Nanoplates with {001} Facets Exposed; Chapter 3: Metal-Based Materials and Alloys; A Study on Mechanical and Fatigue Properties of a Stainless Steel; Development of 590MPa Grade Hot-Dip Galvannealed DP Steels; Effect of Annealing Temperature on Microstructure and Damping Capacity of Twin Roll Cast ZK60 Alloy 327 $aEffect of Ca and Nd Alloying on the Microstructure of Mg-6Al-Ca-Nd Alloy Effect of Cu on the Electrochemical Corrosion Behavior of Sn-8Zn-3Bi Lead-Free Solder Alloy; Effect of Electropulsing Rolling on the Microstructure and Properties of Industrial Pure Titanium TA1; Effect of Er on Microstructure and Hardness of Al-Zn-In Alloy; Effect of Grain Size on Microstructure and Orientation of Fe-25Mn-3Si-3Al Steel; Effect of Nd on Primary Silicon and Mechanical Properties of Hypereutectic Al-17.5%Si Alloy; Experiment and Analyses on 16 Mn Steel under Cyclic Loading Controlled by Strain 327 $aExperimental Study on the Effect of Retained Austenite on the Impact Toughness of a Low-Carbon Martensite Steel Galvanic Corrosion of 70-30 Copper-Nickel Alloy in Contact with Nickel-Aluminum Bronze in Simulated Deep Sea Environment; High Temperature Oxidation Investigation of Hot Roll Material with High-Speed Steel; Influence of Neodymium on Wear Resistance of Hypereutectic Al-Si Alloy; Influence of Pre-Deformation Strain on Recovery Performance of Ni47Ti44Nb9 Alloy ?8mm Pipe Joint 327 $aInfluence of Solution Treatment on the Microstructure and Mechanical Properties of an Deformed Al-12.7Si-0.7Mg Alloy 330 $aCollection of selected, peer reviewed papers from the 2014 5th International Conference on Advances in Materials and Manufacturing (ICAMMP 2014), December 20-21, 2014,Fuzhou, China. The 192 papers are grouped as follows: Chapter 1: Composites; Chapter 2: Low-dimensional and Nano-Materials; Chapter 3: Metal-based Materials and Alloys; Chapter 4: Building and Construction Materials; Chapter 5: Biomaterials and Technologies; Chapter 6: Chemical Materials and Technologies; Chapter 7: Material Testing, Characterization and Applications; Chapter 8: Surface Engineering and Coating Technology; Chapter 410 0$aAdvanced materials research ;$vVolume 1095. 606 $aManufacturing processes$vCongresses 606 $aMaterials$vCongresses 608 $aElectronic books. 615 0$aManufacturing processes 615 0$aMaterials 676 $a670.42 702 $aJiang$b Zhengyi 702 $aLiu$b Xianghua 801 0$bMiAaPQ 801 1$bMiAaPQ 801 2$bMiAaPQ 906 $aBOOK 912 $a9910460561803321 996 $aAdvances in materials and materials processing V$92051624 997 $aUNINA