06578nam 2200469 450 99646685020331620220723081308.03-030-87668-3(CKB)5470000001298886(MiAaPQ)EBC6796438(Au-PeEL)EBL6796438(OCoLC)1282000657(PPN)258300965(EXLCZ)99547000000129888620220723d2021 uy 0engurcnu||||||||txtrdacontentcrdamediacrrdacarrier6th International Conference on Adhesive Bonding 2021 selected contributions of AB 2021 /Lucas F. M. da Silva, Robert D. Adams, editorsCham, Switzerland :Springer,[2021]©20211 online resource (172 pages)Proceedings in engineering mechanics, research, technology and education3-030-87667-5 Intro -- Preface -- Contents -- Open Assembly Time of Water-Borne Polyvinyl Acetate (PVAc) Wood Adhesives Affected by Various Factors -- 1 Introduction -- 2 Materials and Methods -- 2.1 Adhesive System Characteristics -- 2.2 Experimental Designs -- 2.3 Influence of Temperature on Viscosity -- 2.4 Procedure for Determining the Open Time -- 2.5 Statistical Analyses -- 3 Results and Discussion -- 4 Conclusion -- References -- Engineering Technology and Preparation of Coating Systems Made with Epoxy Resin-Based Bonding Agents Modified with the Addition of Granite Powder Sourced from Quarry Wastes -- 1 Introduction -- 2 Materials and Methods -- 2.1 Concrete Substrate -- 2.2 Waste Granite Powder -- 2.3 Epoxy Resin -- 2.4 Preparation of Coating Systems -- 2.5 Pull-Off Strength Test of Epoxy Resin-Based Bonding Agents -- 3 The Pull-Off Strength Results of the Epoxy Resin Bonding Agent -- 4 Cost-Economic Analysis -- 4.1 Mechanical and Cost Analysis of the Tested Coating -- 5 Conclusions -- References -- Mechanical and Adhesive Properties of Cement-Lime Plasters Modified with Waste Granite Powder -- 1 Introduction -- 2 Materials and Methods -- 2.1 Blend Design of Composites and Sample Preparation -- 2.2 Determination of Consistency of Fresh Mortars -- 2.3 Determination of Volumetric Density of Wet Mortar -- 2.4 Determination of Basic Mechanical Properties of Hardened Mortars -- 2.5 Determination of Adhesion of Hardened Mortars to the Substrate -- 2.6 Water Absorption Test -- 3 Results -- 3.1 Determining the Properties of Fresh Mortars -- 3.2 Determination of Basic Mechanical Properties of Hardened Mortars Modified with Granite Powder -- 3.3 Determination of Adhesion of Hardened Mortars to the Substrate -- 3.4 Water Absorption Test -- 3.5 Comparison of Obrained Results and Literature Review -- 4 Conclusions -- References.Characterization of Fast Adhesive Curing Reactions-A Novel Experimental Setup -- 1 Introduction -- 1.1 Rheology -- 1.2 Basics of Induction Heating -- 1.3 Adhesive Curing Reactions -- 2 Development of a Novel Experimental Setup -- 2.1 Profile Phase -- 2.2 Concept Phase -- 2.3 Prototype -- 3 Conclusions -- References -- Material Extrusion on Enameled Steel Surfaces -- 1 Introduction -- 1.1 Motivation -- 1.2 Objective -- 2 Experimental Setup -- 2.1 Substrate -- 2.2 Pretreatment and Coating -- 2.3 Material Extrusion -- 2.4 Mechanical Characterization -- 3 Results and Discussion -- 4 Conclusion -- References -- The Effect of the Viscosity and the Contact Angle on the Pull-Off Strength of Epoxy Resin Modified with Waste Granite Powders -- 1 Introduction -- 2 Research Significance -- 3 Materials and Methods -- 3.1 Waste Granite Powders -- 3.2 Epoxy Resin and Mixing Proportions of Epoxy Resin with Waste Granite Powders -- 3.3 Viscosity Measurements -- 3.4 Contact Angle Measurements -- 3.5 Pull-Off Strength Test -- 4 Results and Discussion -- 4.1 Viscosity Measurements Results -- 4.2 Contact Angle Measurements Results -- 4.3 Pull-Off Strength Test Results -- 4.4 Dependence of Viscosity and Contact Angle on Pull-Off Strength -- 5 Conclusions -- References -- Investigation of the Cleaning Effectiveness of Laser Radiation for Improved Adhesion on Glass Dust Contaminated Glass Fiber Reinforced Polyamide 6 -- 1 Introduction -- 2 Materials and Methodology -- 3 Results -- 4 Conclusion -- References -- Structural Bonding of Thin-Walled Magnesium Die Cast Components -- 1 Introduction -- 2 Experimental Details -- 3 Results and Discussion -- 3.1 Influence of the Pretreatment -- 3.2 Influence of the Release Agent -- 3.3 Influence of the Type of Flow -- 3.4 Environmental Testing -- 4 Conclusions -- References.The Behaviour of CFRP Adhesive Joints Under Different Loading Rates -- 1 Introduction -- 2 Experimental Details -- 2.1 Adhesive -- 2.2 Adherends -- 2.3 Joint Geometry -- 2.4 Test Conditions -- 3 Numerical Details -- 3.1 Static Analysis -- 3.2 Impact Analysis -- 4 Results and Discussion -- 4.1 Experimental Results-Static Tests -- 4.2 Experimental Results-Impact Tests -- 4.3 Numerical Joint Strength Prediction -- 5 Conclusions -- References -- Long-Term Resistant Bonding Between Wood and Aluminium Alloy for Hybrid Lightweight Composites -- 1 Introduction -- 2 Material and Methods -- 2.1 Material -- 2.2 Methods -- 3 Results and Discussion -- 3.1 Shear Strength of Single Lap Joints -- 3.2 4-Point Bending Strength -- 4 Conclusion -- References -- Multiaxial Fatigue Life Assessment of Adhesive Joints Based on the Concepts of Critical Planes: Stress-Based Approaches -- 1 Introduction -- 2 Stress-Based Multiaxial Fatigue Models -- 2.1 Critical Plane Concepts -- 2.2 Stress-Based Critical Plane Fatigue Models -- 3 Description of the Experimental Program -- 3.1 Materials and Samples -- 3.2 Test Device and Loading Conditions -- 4 Fatigue Life Prediction Procedure -- 4.1 Finite Element Simulation -- 4.2 Critical Plane Fatigue Models Constants -- 5 Results and Discussion -- 5.1 Finite Element Simulation Results -- 5.2 Fatigue Models Evaluation -- 6 Conclusions -- References.Proceedings in Engineering Mechanics Ser.AdhesivesCongressesAdhesives668.3Silva Lucas Filipe Martins da1973-Adams Robert D.MiAaPQMiAaPQMiAaPQBOOK9964668502033166th International Conference on Adhesive Bonding 20212901708UNISA