05341nam 22006253u 450 991100662800332120230120005404.01-84569-347-7(CKB)1000000000415835(EBL)1639734(SSID)ssj0000073024(PQKBManifestationID)11971948(PQKBTitleCode)TC0000073024(PQKBWorkID)10103845(PQKB)10649432(MiAaPQ)EBC1639734(NjHacI)991000000000415835(EXLCZ)99100000000041583520140303d2007|||| u|| |engur|n|---|||||txtccrStandardisation of Thermal Cycling Exposure TestingBurlington Elsevier Science20071 online resource (297 p.)European Federation of Corrosion (EFC) SeriesDescription based upon print version of record.1-84569-273-X Includes bibliographical references and index.Cover; Standardisation of thermal cycling exposure testing; Copyright; Contents; Contributor contact details; European Federation of Corrosion (EFC) publications: Series introduction; Volumes in the EFC series; Foreword; Preface; Acknowledgement; Part I Methods and procedures in thermal cycling oxidation testing prior to COTEST; 1 Survey of existing test procedures and experimental facilities; 1.1 Introduction; 1.2 Summary of layout; 1.3 Temperature control; 1.4 Heating/cooling practice; 1.5 Atmosphere; 1.6 Test pieces - geometry, preparation and handling1.7 Measurement/evaluation techniques1.8 Conclusions; 1.9 References; 2 Compilation of cyclic oxidation data; 2.1 Introduction; 2.2 Cycle length and test duration; 2.3 Materials and environments; 2.4 Variability of results; 2.5 Influence of experimental variables; 2.6 Conclusions; 3 Statistical analysis of cyclic oxidation data; 3.1 Test parameters; 3.2 Comparing and summarising the mass change data; 3.3 Statistical analysis - within sources; 3.4 Statistical analysis - across data sources; 3.5 Number of replicates required for future experiments; 3.6 Conclusions; 3.7 Recommendations3.8 ReferencesPart II Experimental investigations on the influence of test parameter variation on thermal cycling oxidation behaviour; 4 Standardised test procedures, definitions and statistical design of experiments for investigation of test parameter variation on thermal cycling oxidation testing; 4.1 Introduction; 4.2 Preparation of corrosion test specimen and equipment; 4.3 Different thermal cycles investigated; 4.4 Analysis of results and post-test evaluation; 4.5 Statistical design of experiments; 4.6 References; 5 The effect of heating on the total oxidation time; 5.1 Introduction5.2 Heating of the sample5.3 Oxide growth under non-isothermal conditions; 5.4 Influence of the heating phase on the oxidation time; 5.5 Conclusion; 5.6 Acknowledgements; 5.7 References; 6 Investigation of the influence of parameter variation in long dwell thermal cycling oxidation; 6.1 Introduction; 6.2 Experimental set-up; 6.3 Experimental results; 7 Investigation of the influence of parameter variation in short dwell thermal cycling oxidation; 7.1 Introduction; 7.2 Experimental investigation of reference materials under internally standardised thermal cycling oxidation conditions7.3 References8 Investigation of the influence of parameter variation in ultra-short dwell thermal cycling oxidation; 8.1 Introduction; 8.2 Definition of suitable test conditions; 8.3 Possible alternative test procedures; 8.4 Design of a 'focused light' rapid thermal cycle test facility; 8.5 Design of a Joule heating device for wire and foil materials; 8.6 Ultra-short dwell experiments; 8.7 Conclusions; 9 Burner rig thermal cycling oxidation testing; 9.1 Introduction; 9.2 Low-velocity burner rig; 9.3 High-velocity burner rig; 9.4 References10 Thermal cycling oxidation testing in sulphidising atmospheresThe thermal cyclic oxidation test has become one of the most widely accepted ways of measuring high temperature corrosion. There has long been a need for an agreed code of practice with standardised methods and procedures to ensure both the comparability and reliability of the results obtained. Based on an EU project, 'Cyclic oxidation testing - development of a code of practice for the characterisation of high temperature materials performance' (COTEST), this volume provides the essential background to an appropriate code of practice.The first part of the book reviews the range of exiEuropean Federation of Corrosion (EFC) SeriesEuropean Federation of Corrosion STANDARDISATION OF THERMAL CYCLING EXPOSURE TESTING Materials at high temperaturesOxidationMaterials at high temperatures.Oxidation.547.23Schütze M1822295Malessa M1822714AU-PeELAU-PeELAU-PeELBOOK9911006628003321Standardisation of Thermal Cycling Exposure Testing4389061UNINA