05505nam 2200649 450 991081804140332120200903223051.03-03826-525-X(CKB)3710000000214598(EBL)1910837(SSID)ssj0001379232(PQKBManifestationID)11809607(PQKBTitleCode)TC0001379232(PQKBWorkID)11351699(PQKB)10734128(Au-PeEL)EBL1910837(CaPaEBR)ebr10906054(OCoLC)891381166(MiAaPQ)EBC1910837(EXLCZ)99371000000021459820140822h20142014 uy 0engur|n|---|||||txtccrHigh speed machining VI selected, peer reviewed papers from the 6th international conference on high speed machining (ICHSM2014), July 24-25, 2014, Harbin, China /edited by Xianli Liu [and three others]Switzerland :Trans Tech Publications,2014.Switzerland :Trans Tech Publications,[date of distribution not identified]©20141 online resource (890 p.)Materials Science Forum,0255-5476 ;Volumes 800-801Includes indexes.3-03835-142-3 High Speed Machining VI; Preface, Committees and Sponsors; Table of Contents; Chapter 1: Mechanisms and Machining Process; Research Progress of High Speed Cutting for SiCp_Al Composite Materials; Experimental Study of the Corner of Hardened Steel Mould in High Speed Milling with Micro-End Mill; Experimental Study on Surface Quality at Different Milling Speed of High Volume Fraction SiCp/Al Thin Walled Test-Piece; Research on Tool Wear of PCD Micro End Mill in Machining of ZrO2 Ceramics; The Machinability Comparison of Laser Solid Forming (LSF) and Forging TC4 AlloysMilling Forces of Compacted Graphite Iron (CGI) and Gray Iron (GI)Bioactive Film Generation during Titanium Alloy Cutting in Oxygen-Enriched Atmosphere; Investigation of Cutting Force and Tool Wear in High Speed Milling of GH4169 Using Ceramic Tools; Investigation on Processing Technology in Machining CFRP Large Size Hole; Milling Force Modeling and Experimental Research of 300M Ultra High Strength Steel; Defects Study on Drilling of Carbon Fiber Reinforced Polymer (CFRP) Laminates; Experiment on Magnetization of High-Speed Steel Cutting ToolHigh Temperature Alloy of Turning Processing Characteristic and Process AnalysisExperimental Study on Orthogonal Cutting of 0° T700/LT03A CFRP Uniform Laminates; Experimental Investigation of Tool Wear and Chip Morphology in Turning Titanium Alloy Ti6Al4V; Research on the Cutting Property of Ceramic Tool Cutting Nickel Based Superalloy GH4169; Investigations on the Machinability of Titanium Alloy TC25; An Experimental Study on Optimization of Cutting Parameters for Disk Milling Titanium Blisk; Research on the Wear Process of High Speed Cutting Ni-Based SuperalloyExperiment Research on Chips Flying Characteristics for Heavy-Duty MillingInvestigation of Chip Morphology in High-Speed Milling of Nickel-Based Superalloy GH706; Study on Drilling Characteristics of Supper Alloy GH3039; Effect of High-Temperature Alloy Cutting Speed on Tool Wear; Determination of Unit Cutting Force of GH4698 Broaching; Investigation on Milling Force with Tilt Angles in Milling Cr12MoV; Application of High Speed Machining Technology in Modern Die Manufacture; Study on Force Characteristics for High Speed Sawing of Quartz Glass with Diamond BladeChip Formation in High-Speed Milling of Titanium Alloy with PCD ToolsResearch on Wear Surface Morphology of PCBN Tools in High-Speed Machining Valve Seat Insert; Surface Roughness Prediction and Experimental Analysis in Grinding the Material of Zirconia Used by Dental Restoration; Research on Micro Machining of Slit Grating; Cutting Force Analysis in Tool Condition Monitoring of Difficult to Cut Materials; Investigation of Tool-Wear and Surface Roughness in Turning Ti6Al4V under Different Cooling Lubrication Conditions; Research on Fractal Characterization in Grinding of Monocrystal SapphireExperimental Study on Turning Nickel-Based Superalloy GH4033 with Coated Cemented Carbide ToolsCollection of selected, peer reviewed papers from the 6th International Conference on High Speed Machining (ICHSM2014), July 24-25, 2014, Harbin, China. The 160 papers are grouped as follows: Chapter 1: Mechanisms and Machining Process, Chapter 2: Modeling and Simulation of Machining Processes, Chapter 3: Machine Tools and Cutting Tools, Chapter 4: Surface Integrity of Machining Processes, Chapter 5: CAD/CAM and Process Optimization, Chapter 6: Testing, Measuring and Monitoring of Processing, Chapter 7: Micro-Machining and Non-Traditional Machining Technologies About 150 papers consider high-sMaterials science forum ;Volumes 800-801.High-speed machiningCongressesMetal-cutting toolsCongressesHigh speed machiningICHSMHigh-speed machiningMetal-cutting tools671.35Liu XianliMiAaPQMiAaPQMiAaPQBOOK9910818041403321High speed machining VI3940694UNINA