| |
|
|
|
|
|
|
|
|
1. |
Record Nr. |
UNINA9910820212003321 |
|
|
Titolo |
Manufacturing engineering : selected, peer reviewed papers from the 1st International Manufacturing Engineering Conference (iMEC 2013), July 1-3, 2013, Gambang, Kuantan, Pahang, Malaysia / / edited by Ahmad Razlan Yusoff and Ismed Iskandar |
|
|
|
|
|
|
|
Pubbl/distr/stampa |
|
|
Zurich, Switzerland : , : TTP, , 2014 |
|
©2014 |
|
|
|
|
|
|
|
|
|
ISBN |
|
|
|
|
|
|
Descrizione fisica |
|
1 online resource (470 p.) |
|
|
|
|
|
|
Collana |
|
Advanced Materials Research, , 1662-8985 ; ; Volume 903 |
|
|
|
|
|
|
Disciplina |
|
|
|
|
|
|
Soggetti |
|
|
|
|
|
|
Lingua di pubblicazione |
|
|
|
|
|
|
Formato |
Materiale a stampa |
|
|
|
|
|
Livello bibliografico |
Monografia |
|
|
|
|
|
Note generali |
|
Description based upon print version of record. |
|
|
|
|
|
|
Nota di bibliografia |
|
Includes bibliographical references and indexes. |
|
|
|
|
|
|
Nota di contenuto |
|
Manufacturing Engineering; Preface, Organizing Committees and Sponsors; Table of Contents; Chapter 1: Materials and Manufacturing Process; Drilling of Carbon Fibre Composites: A Review; Tool Life and Flank Wear of Physical Vapour Deposited TiAlN Multilayer Coated Carbide End Mill Inserts when Machining AISI D2 Hardened Steel under Dry Cutting Condition; Effect of Tool Path Strategies in Pocket Milling of Aluminium Epoxy; Effect of Cutting Parameters on Tool-Chip Interface Temperature in an Orthogonal Turning Process; Finite Element Analysis of Aluminum-Kevlar/Epoxy Pressure Vessel |
Frictional Characteristics of Steel Materials Sliding against Mild SteelEffect of Different Qualities of Foam on Fill Particle Transport in Horizontal Well Cleanup Operation Using Coiled Tubing; Dry and Compressed Air Cooling Comparative Study on 6061 Aluminium Alloy Drilling Using Coated Drill; Influence of Workpiece Shape on MRR and EWR in EDM of Steel; The Effect of EDM Die-Sinking Parameters on Non-Conductive Materials; The Effect of Pressure on Warpage of Dumbbell Plastic Part in Injection Moulding Machine |
Feasibility Study of Casted Natural Fibre-LM6 Composites for Engineering ApplicationThe Structural and Surface Morphology of Annealed ZnO Films; Surface Roughness of Casted LM6 Using Natural Fibre Sand Casting Mould; Assessment of Machining Cost for End- |
|
|
|
|
|
|
|
|
|
|
|
Milling of Ti-6Al-4V Titanium Alloy through RSM-Based Parametric Model; Experimental Investigation on Friction Coefficient of Engineering Polymers Sliding against Different Counterface Materials; Experimental Investigation on Static Mechanical Properties of Glass/Carbon Hybrid Woven Fabric Composite Laminates |
Photoluminescene and Fourier Transform Infrared Measurement of Undoped Diamond-Like Carbon Thin Films by Direct Current - Plasma Enhanced Chemical Vapour DepositionEffect of Substrate Temperature on Structural and Optical Properties of Un-Doped Diamond Thin Film; Microstructure and Tensile Strength of Rapid Manufacturing Parts; Thermal Performance of Polyamide 6/Cloisite 20A Composite Hybrid by Adiabatic Extrusion: A Study on the Influence of Difference Approach of Compounding; Experimental Study of the Static Modal Analysis on Milling Machine Tool |
Optimization of Electro Discharge Machining Parameters for Drilling Titanium in Small Holes Using Taguchi MethodThe Effect of Vortex Tube Cooling on Surface Roughness and Carbon Footprint in Dry Turning; Study on Potential Waste Insulating Material Properties in Water for Thermal Storage Application; Effect of TiC Particulates on the Microstructure and Mechanical Properties of Aluminium-Based Metal Matrix Composite; Studies on Tensile Properties of Titanium Carbide (TiC) Particulates Composites; Review of Aluminum Chip Machining Using Direct Recycling Process |
Comparison of Cooling Performance between High Thermal Conductivity Steel (HTCS 150) and Hot Work Tool Steel (SKD 61) Insert for Experimental Tool Using Finite Element Analysis |
|
|
|
|
|
|
Sommario/riassunto |
|
Collection of selected, peer reviewed papers from the 1st International Manufacturing Engineering Conference (iMEC 2013), July 1-3, 2013, Gambang, Kuantan, Pahang, Malaysia. The 75 papers are grouped as follows: Chapter 1: Materials and Manufacturing Process, Chapter 2: Engineering, Manufacturing Automation and Optimization, Chapter 3: Manufacturing Systems and Management |
|
|
|
|
|
|
|
| |