| |
|
|
|
|
|
|
|
|
1. |
Record Nr. |
UNINA9910692697803321 |
|
|
Titolo |
Endangered species [[electronic resource] ] : more federal management attention is needed to improve the consultation process : report to congressional requesters |
|
|
|
|
|
|
|
Pubbl/distr/stampa |
|
|
[Washington, D.C.] : , : U.S. General Accounting Office, , [2004] |
|
|
|
|
|
|
|
Soggetti |
|
Endangered species - United States |
Environmental mediation - United States |
|
|
|
|
|
|
|
|
Lingua di pubblicazione |
|
|
|
|
|
|
Formato |
Materiale a stampa |
|
|
|
|
|
Livello bibliografico |
Monografia |
|
|
|
|
|
Note generali |
|
Title from title screen (viewed on July 27, 2004). |
"March 2004." |
Paper version available from: U.S. General Accounting Office, 441 G St., NW, Rm. LM, Washington, D.C. 20548. |
"GAO-04-93." |
|
|
|
|
|
|
|
|
Nota di bibliografia |
|
Includes bibliographical references. |
|
|
|
|
|
|
|
|
|
|
|
|
|
2. |
Record Nr. |
UNINA9910813917203321 |
|
|
Titolo |
Materials, manufacturing engineering and information technology : selected, peer reviewed papers from the 2014 2nd International Conference on Advanced Composite Materials and Manufacturing Engineering (CMME 2014), Marcj 22-23, Wuhan, China / / edited by B. Xu and H. Y. Li |
|
|
|
|
|
|
|
Pubbl/distr/stampa |
|
|
Durnten-Zurich, Switzerland : , : Trans Tech Publications, , 2014 |
|
Durnten-Zurich, Switzerland ; ; Enfield, New Hampshire : , : distributed worldwide by Trans Tech Publications, , [date of distribution not identified] |
|
©2014 |
|
|
|
|
|
|
|
|
|
ISBN |
|
|
|
|
|
|
Descrizione fisica |
|
1 online resource (471 p.) |
|
|
|
|
|
|
Collana |
|
Advanced Materials Research, , 1662-8985 ; ; Volume 910 |
|
|
|
|
|
|
Disciplina |
|
|
|
|
|
|
Soggetti |
|
Manufacturing processes |
Industrial engineering |
Materials science |
Information technology |
|
|
|
|
|
|
|
|
Lingua di pubblicazione |
|
|
|
|
|
|
Formato |
Materiale a stampa |
|
|
|
|
|
Livello bibliografico |
Monografia |
|
|
|
|
|
Note generali |
|
Description based upon print version of record. |
|
|
|
|
|
|
Nota di bibliografia |
|
Includes bibliographical references at the end of each chapters and indexes. |
|
|
|
|
|
|
|
|
Nota di contenuto |
|
Materials, Manufacturing Engineering and Information Technology; Preface, Committees and Sponsors; Table of Contents; Chapter 1: Material Science; Bottom-Up Fabrication of Optical Metamaterials; Co3O4 Nanoparticles Prepared by Precipitation; The Effect of Temperature on the NiCu Coating Prepared by Electroplating; The Influence of pH Value on the NiCu Coating Synthesized by Electroplating; Preparation and Properties of Alcohol-Soluble Acrylate Adhesive; Preparation and Properties of Porous Hydroxyapatite Ceramics by Three Dimensional Stacking with Homogeneous Fibers |
Corrosion Behavior of Phosphate Conversion Coating on AZ31 Mg Alloy in 3.5% NaCl SolutionFlammability and Thermal Degradation of PMMA/Graphene Composites; AE Characterization of Cracking Mode in Sandstone Uniaxial and Brazilian Tests; Early Effect for 28nm HK/MG |
|
|
|
|
|
|
|
|
|
|
|
PMOSFETs after Post Deposition Annealing Treatment; Threshold Voltage Adjustment for 28nm HfOx/ZrOx/HfOx Gate Dielectric of nMOSFETs Using DPN Process with Annealing Temperatures; Influence of Structural Relaxation on Compressive Plasticity of Zr64.13Cu15.75Ni10.12Al10 Bulk Metallic Glass |
Preparation and Analyzing Character of Chitosan Block in Fluffy Meshwork Shape Formed from Chitosan Fine HairDeep Desulfurization of Diesel Fuel Oxidized with TBHP Coupled with Solvent Extraction Intensified by Ultrasound; An Orthogonal Experimental Analysis of WEDM-HS of Al2O3 Particle-Reinforced Aluminum Alloy 6061 with 10-Vol% Al2O3; Research on Biological Materials for the Preferred of the Chlorophyll Content Gray GM (1,1) Prediction Models Based on the Different Light; Toughening of Epoxy Resin Modified with In Situ Polymerized Acrylate Copolymer |
Study on Elastic Modulus of Porous Ti Coatings by Three-Point Bending and Indentation MeasurementEvaluation of Acoustic Characteristics for Various Composite Ventilation Material by Using Impedance Tube; Effect of Vermiculite and Bulk Density in the PU Foam Composite Board for the Absorption Coefficient and Acoustic Impedance; Low-Phosphorus Electroless Nickel-Coated Carbon Fibers; Experimental and Theoretical Investigation of Flexure Behavior and Failure Mode of Filament-Wound Composite Tube; Experimental Research on Rheological Properties of Slick Water Mixed with CO2 System |
Preparation and Properties of BR/SBR Blends Using Surface-Modified Nano Zinc OxideEffects of Fiber Component on Tensile Properties of Composites; Recovery of Metal Values from Low-Grade Heterogenite with Reductive Ammonia Leaching Method; Study on Milling Force of High Volume Fraction SiCp/Al Composites with Ultrasonic Longitudinal and Torsional Vibration High Speed Milling; Vanadium & Titanium's Effects on High Strength Weathering Steel's Impact Toughness in CGHAZ; Simulation of Fixed Bed Reactor for the Dehydration Reaction from Alcohol Gas to Ethylene |
Mechanical Property for the Combining Yarn of BF/GF and Polypropylene |
|
|
|
|
|
|
Sommario/riassunto |
|
Collection of selected, peer reviewed papers from the 2014 2nd International Conference on Advanced Composite Materials and Manufacturing Engineering (CMME 2014), March 22-23, 2014, Wuhan, China. The 104 papers are grouped as follows: Chapter 1: Material Science, Chapter 2: Applied Mechanics, Chapter 3: Mechanical Engineering, Chapter 4: Information Technology and Applied Research |
|
|
|
|
|
|
|
| |