| |
|
|
|
|
|
|
|
|
1. |
Record Nr. |
UNINA9910786765203321 |
|
|
Titolo |
High speed machining VI : selected, peer reviewed papers from the 6th international conference on high speed machining (ICHSM2014), July 24-25, 2014, Harbin, China / / edited by Xianli Liu [and three others] |
|
|
|
|
|
|
|
Pubbl/distr/stampa |
|
|
Switzerland : , : Trans Tech Publications, , 2014 |
|
Switzerland : , : Trans Tech Publications, , [date of distribution not identified] |
|
©2014 |
|
|
|
|
|
|
|
|
|
ISBN |
|
|
|
|
|
|
Descrizione fisica |
|
1 online resource (890 p.) |
|
|
|
|
|
|
Collana |
|
Materials Science Forum, , 0255-5476 ; ; Volumes 800-801 |
|
|
|
|
|
|
Disciplina |
|
|
|
|
|
|
Soggetti |
|
High-speed machining |
Metal-cutting tools |
|
|
|
|
|
|
|
|
Lingua di pubblicazione |
|
|
|
|
|
|
Formato |
Materiale a stampa |
|
|
|
|
|
Livello bibliografico |
Monografia |
|
|
|
|
|
Note generali |
|
|
|
|
|
|
Nota di contenuto |
|
High Speed Machining VI; Preface, Committees and Sponsors; Table of Contents; Chapter 1: Mechanisms and Machining Process; Research Progress of High Speed Cutting for SiCp_Al Composite Materials; Experimental Study of the Corner of Hardened Steel Mould in High Speed Milling with Micro-End Mill; Experimental Study on Surface Quality at Different Milling Speed of High Volume Fraction SiCp/Al Thin Walled Test-Piece; Research on Tool Wear of PCD Micro End Mill in Machining of ZrO2 Ceramics; The Machinability Comparison of Laser Solid Forming (LSF) and Forging TC4 Alloys |
Milling Forces of Compacted Graphite Iron (CGI) and Gray Iron (GI)Bioactive Film Generation during Titanium Alloy Cutting in Oxygen-Enriched Atmosphere; Investigation of Cutting Force and Tool Wear in High Speed Milling of GH4169 Using Ceramic Tools; Investigation on Processing Technology in Machining CFRP Large Size Hole; Milling Force Modeling and Experimental Research of 300M Ultra High Strength Steel; Defects Study on Drilling of Carbon Fiber Reinforced Polymer (CFRP) Laminates; Experiment on Magnetization of High-Speed Steel Cutting Tool |
High Temperature Alloy of Turning Processing Characteristic and |
|
|
|
|
|
|
|
|
|
|
|
Process AnalysisExperimental Study on Orthogonal Cutting of 0° T700/LT03A CFRP Uniform Laminates; Experimental Investigation of Tool Wear and Chip Morphology in Turning Titanium Alloy Ti6Al4V; Research on the Cutting Property of Ceramic Tool Cutting Nickel Based Superalloy GH4169; Investigations on the Machinability of Titanium Alloy TC25; An Experimental Study on Optimization of Cutting Parameters for Disk Milling Titanium Blisk; Research on the Wear Process of High Speed Cutting Ni-Based Superalloy |
Experiment Research on Chips Flying Characteristics for Heavy-Duty MillingInvestigation of Chip Morphology in High-Speed Milling of Nickel-Based Superalloy GH706; Study on Drilling Characteristics of Supper Alloy GH3039; Effect of High-Temperature Alloy Cutting Speed on Tool Wear; Determination of Unit Cutting Force of GH4698 Broaching; Investigation on Milling Force with Tilt Angles in Milling Cr12MoV; Application of High Speed Machining Technology in Modern Die Manufacture; Study on Force Characteristics for High Speed Sawing of Quartz Glass with Diamond Blade |
Chip Formation in High-Speed Milling of Titanium Alloy with PCD ToolsResearch on Wear Surface Morphology of PCBN Tools in High-Speed Machining Valve Seat Insert; Surface Roughness Prediction and Experimental Analysis in Grinding the Material of Zirconia Used by Dental Restoration; Research on Micro Machining of Slit Grating; Cutting Force Analysis in Tool Condition Monitoring of Difficult to Cut Materials; Investigation of Tool-Wear and Surface Roughness in Turning Ti6Al4V under Different Cooling Lubrication Conditions; Research on Fractal Characterization in Grinding of Monocrystal Sapphire |
Experimental Study on Turning Nickel-Based Superalloy GH4033 with Coated Cemented Carbide Tools |
|
|
|
|
|
|
Sommario/riassunto |
|
Collection of selected, peer reviewed papers from the 6th International Conference on High Speed Machining (ICHSM2014), July 24-25, 2014, Harbin, China. The 160 papers are grouped as follows: Chapter 1: Mechanisms and Machining Process, Chapter 2: Modeling and Simulation of Machining Processes, Chapter 3: Machine Tools and Cutting Tools, Chapter 4: Surface Integrity of Machining Processes, Chapter 5: CAD/CAM and Process Optimization, Chapter 6: Testing, Measuring and Monitoring of Processing, Chapter 7: Micro-Machining and Non-Traditional Machining Technologies About 150 papers consider high-s |
|
|
|
|
|
|
|
| |