| |
|
|
|
|
|
|
|
|
1. |
Record Nr. |
UNINA9910464898803321 |
|
|
Titolo |
Advances in applied mechanics and materials : selected, peer reviewed papers from the International Conference on Mechanical Engineering (ICOME 2013), September 19-21, 2013, Mataram, Lombok, Indonesia / / edited by Bambang Pramujati |
|
|
|
|
|
|
|
Pubbl/distr/stampa |
|
|
Durnten-Zurich : , : TTP, , [2014] |
|
©2014 |
|
|
|
|
|
|
|
|
|
ISBN |
|
|
|
|
|
|
Descrizione fisica |
|
1 online resource (800 p.) |
|
|
|
|
|
|
Collana |
|
Applied mechanics and materials, , 1660-9336 ; ; volume 493 |
|
|
|
|
|
|
Altri autori (Persone) |
|
|
|
|
|
|
Soggetti |
|
Mechanics, Applied |
Electronic books. |
|
|
|
|
|
|
|
|
Lingua di pubblicazione |
|
|
|
|
|
|
Formato |
Materiale a stampa |
|
|
|
|
|
Livello bibliografico |
Monografia |
|
|
|
|
|
Note generali |
|
Description based upon print version of record. |
|
|
|
|
|
|
Nota di bibliografia |
|
Includes bibliographical references and indexes. |
|
|
|
|
|
|
Nota di contenuto |
|
Advances in Applied Mechanics and Materials; Editorial Note; Table of Contents; Chapter 1: Energy Conversion; Design of a Bubbling Fluidized Bed Gasifier for the Thermochemical Conversion of Oil Palm Empty Fruit Bunch Briquette; Laminar Flow Past a Circular Cylinder: Reduction of Drag and Fluctuating Lift Using Upstream and Downstream Rods; Trans-Esterification of Triglycerides with Methanol on Sulfated Zirconia Prepared with Different Concentration of Sulfuric Acid; Numerical Studies on R22 Refrigerant Compressor Using Environment Friendly Working Fluids |
Case Studies Thermal Analysis of HP Condensate Stabilizer ColumnThe Influence of Hydrogen Addition to Diesel Fuel Spray Combustion for Different Atomization Conditions; Hydrogen Production from Acetic Acid Steam Reforming over Bimetallic Ni-Co on La2O3 Catalyst-Effect of the Catalyst Dilution; Driving Efficiency through Hydrocarbon for Green Car Air Conditioning; Air to Air Ejector with Various Divergent Mixing Chambers; Kamojang Geothermal Power Plant Unit-1 : 30 Years of Operation; Flow Visualization Pattern on Sharp Edge T-Junction through Dividing Flow Channel |
An Experimental Study on the Vertical Flow Past a Finite-Length Horizontal Cylinder at Low Reynolds NumbersEffect of Air Conditioning |
|
|
|
|
|
|
|
|
|
|
|
Position on Thermal Comfort in the Floor Air Conditioning System; Computational Fluid Dynamic Using Parallel Loop of Multi-Cores Processor; Experimental Studies on a Solar Air Heater Having V-Corrugated Absorber Plate with Obstacles Bent Vertically; Energy Savings in Air Conditioning System Using Ejector: An Overview; Empirical Correlations for Sizing Adiabatic Capillary Tube Using LPG as Refrigerant in Split-Type Air-Conditioner |
Validation of AWTSim as Aerodynamic Analysis for Design Wind Turbine BladeNumerical Study on the Influence of the Corner Curvature of Circular Micropillar on Microdroplet Size via a Dewetting Process; Redesign ITS Central Library through Smart Building; Optimization of Maximum Lift to Drag Ratio on Airfoil Design Based on Artificial Neural Network Utilizing Genetic Algorithm; Carbon Dioxide Effects on the Flammability Characteristics of Biogas; Heat Transfer Effectiveness and Coefficient of Pressure Drop on the Shell Side of a Staggered Elliptical Tubes Bank |
Experimental Study on the Effect of Reynolds Number Variation on Drag Force for Various Cut Angle on D-Type CylindersPerformance of Conical Diffuser on Liquid Jet Gas Ejector; An Investigation into the Effect of Drag Coefficient on Overtaking of Car; Effects of Pine Oil on Dynamics of Bubble in Froth Flotation; Study on Auto-Ignition Behavior of Lubricating Oil in a Cone Calorimeter; Solar Driven Absorption Chiller for Medium Temperature Food Refrigeration, a Study for Application in Indonesia; The Effect of Water Droplet Size on the Extinguished Concentric Jet Premixed and Diffusion Flame |
Gaining the Enthalpy of Solid Yields Formation in the Process of Waste Pyrolysis |
|
|
|
|
|
|
Sommario/riassunto |
|
Collection of selected, peer reviewed papers from the International Conference on Mechanical Engineering (ICOME 2013), September 19-21, 2013, Mataram, Lombok, Indonesia. The 130 papers are grouped as follows: Chapter 1: Energy Conversion; Chapter 2: Mechanical Design; Chapter 3: Manufacturing Processes and Technologies; Chapter 4: Material Science and Engineering |
|
|
|
|
|
|
|
| |