| |
|
|
|
|
|
|
|
|
1. |
Record Nr. |
UNINA9910459980503321 |
|
|
Titolo |
Advanced materials and structures V : selected, peer reviewed papers from the fifth International Conference on Advanced Materials and Structures (AMS 2013), October 24-25, 2013, Timișoara, Romania / / edited by Mircea Nicoara and Carmen Opris |
|
|
|
|
|
|
|
Pubbl/distr/stampa |
|
|
Pfaffikon, Switzerland : , : TTP, , 2014 |
|
©2014 |
|
|
|
|
|
|
|
|
|
ISBN |
|
|
|
|
|
|
Descrizione fisica |
|
1 online resource (338 p.) |
|
|
|
|
|
|
Collana |
|
Solid State Phenomena, , 1662-9779 ; ; Volume 216 |
|
|
|
|
|
|
Disciplina |
|
|
|
|
|
|
Soggetti |
|
Materials |
Biomedical materials |
Electronic books. |
|
|
|
|
|
|
|
|
Lingua di pubblicazione |
|
|
|
|
|
|
Formato |
Materiale a stampa |
|
|
|
|
|
Livello bibliografico |
Monografia |
|
|
|
|
|
Note generali |
|
Description based upon print version of record. |
|
|
|
|
|
|
Nota di bibliografia |
|
Includes bibliographical references at the end of each chapters and indexes. |
|
|
|
|
|
|
|
|
Nota di contenuto |
|
Advanced Materials and Structures V; Preface, Committees and Sponsor; Table of Contents; Chapter 1: Advanced Materials; About Replacement of Nickel as Amorphization Element for Fabrication of Ultra-Rapidly Solidified Ti-Zr Alloys; The Effect of Mo and Al on the Corrosion Behavior of Titanium and Some of its Alloys for Biomedical Applications; Structural Characteristics of Ductile Iron at Different Rare Earth Contribution from a Magnesium Ferrosilicon Alloy; Correlation between Microstructure and Magnetic Properties on MnZn Ferrite with Bi2O3 Increasing Addition |
Composite Powder and Compacts of Iron/Iron Oxide Type Produced by Mechanosynthesis and Reactive SinteringCrystallization of Ni-Cr-Si-B and Ni-Cr-Fe-Si-B Amorphous Alloys; Implant Surface Finishing Influence on Tissue-Implant Anchoring; Mechanical Behavior of Fe60Co14Ga2P10B5Si3Al3C3 Bulk Metallic Glass; The Influence of Sulphur and Oxigen Additions in Mg-Treated Iron on the Cooling Curves Parameters; Research on the Influence of Pelleting Mixture Components on Chemical Components and Pellets Structure; Chapter 2: Materials Characterization |
|
|
|
|
|
|
|
|
|
|
|
Joint Quality Assessment of Three Different Laser Welded Dental AlloysDescription of Degradation Process of Rubberized Lean Concrete; Influence of Cooling Rate on the Structural Characteristics of Ca and Rare Earth Inoculated, Low-S Grey Cast Iron; Influence of the Si-Content on the High Temperature Oxidation Behaviour of NiCrBSi-Coatings; A Study on Metal-Ceramic Thermal Expansion Compatibility; An Evaluation of Sn-Cu-Ga and Sn-Cu-Ag Solder Alloys for Applications within the Electronics Industry |
Analysis of Hazards Identified within the Premises of the Electric Steelworks, to Carry out the Risk AssessmentComputation of HAZ Hardness for Low Alloyed Welded Steels Using Five-Parameter Logistic Function; Damage Detection in Flux Cored Wire Welded Structures by Using Vibration Testing; Determination of Flexural Properties of Rigid PUR Foams Using Digital Image Correlation; Effects of Silicon Carbide Proportion and Artificial Aging Parameters on Microstructure and Hardness of Al-Cu/SiCp Composites |
Experimental and Numerical Investigations of TBC Behaviour after Aging, Subjected to Tension and BendingDetermination of Mechanical Properties of Chondrocytes in Articular Cartilage Using Atomic Force Microscopy; Heat Transfer in Composites Subjected to Temperature Variations; Influence of Milling Time on the Homogeneity of the Al2O3/Ni Composite Powders Obtained by Mechanical Milling; Measurement of Young's Modulus and Shear Modulus of Some Structures Welded Using Flux Cored Wire by Vibration Tests |
Mechanical Effects of Simulated Pressure and Temperature Conditions on Porcelain Dental Bridges |
|
|
|
|
|
|
Sommario/riassunto |
|
Collection of selected, peer reviewed papers from the the Fifth International Conference on Advanced Materials and Structures (AMS 2013), 24-25 October 2013, Timişoara, Romania. The 56 papers are grouped as follows: Chapter 1: Advanced Materials, Chapter 2: Materials Characterization, Chapter 3: Modern Processing Techniques |
|
|
|
|
|
|
|
| |