| |
|
|
|
|
|
|
|
|
1. |
Record Nr. |
UNICASRML0292267 |
|
|
Titolo |
4: Il Settecento |
|
|
|
|
|
Pubbl/distr/stampa |
|
|
Roma - Bari, : Laterza, 1996 |
|
|
|
|
|
|
|
ISBN |
|
|
|
|
|
|
Descrizione fisica |
|
|
|
|
|
|
Lingua di pubblicazione |
|
|
|
|
|
|
Formato |
Materiale a stampa |
|
|
|
|
|
Livello bibliografico |
Monografia |
|
|
|
|
|
2. |
Record Nr. |
UNINA9910145084003321 |
|
|
Titolo |
Research notes / / Laurentian Forestry Centre |
|
|
|
|
|
Pubbl/distr/stampa |
|
|
Sainte-Foy, Quebec, : The Centre, 1997- |
|
|
|
|
|
|
|
Descrizione fisica |
|
|
|
|
|
|
Classificazione |
|
|
|
|
|
|
|
|
Disciplina |
|
|
|
|
|
|
Soggetti |
|
Forests and forestry |
Forests and forestry - Research - Canada - Periodicals |
forest management |
land restoration |
afforestation |
Forests and forestry - Research |
Periodicals. |
Canada |
|
|
|
|
|
|
|
|
Lingua di pubblicazione |
|
|
|
|
|
|
Formato |
Materiale a stampa |
|
|
|
|
|
Livello bibliografico |
Periodico |
|
|
|
|
|
Note generali |
|
Each issue also has a distinctive title. |
Title from caption. |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
3. |
Record Nr. |
UNINA9910872854603321 |
|
|
Titolo |
1997 44th Annual Petroleum and Chemical Industry Conference |
|
|
|
|
|
Pubbl/distr/stampa |
|
|
[Place of publication not identified], : IEEE, 1997 |
|
|
|
|
|
|
|
Descrizione fisica |
|
1 online resource (300 pages) |
|
|
|
|
|
|
Disciplina |
|
|
|
|
|
|
Soggetti |
|
Petroleum industry and trade - Electric equipment |
Chemical industry - Energy conservation |
|
|
|
|
|
|
|
|
Lingua di pubblicazione |
|
|
|
|
|
|
Formato |
Materiale a stampa |
|
|
|
|
|
Livello bibliografico |
Monografia |
|
|
|
|
|
Note generali |
|
Bibliographic Level Mode of Issuance: Monograph |
|
|
|
|
|
|
Nota di contenuto |
|
Record of Conference Papers. IEEE Industry Applications Society 44th Annual Petroleum and Chemical Industry Conference -- Induction motors, reciprocating compressors and variable frequency drives -- A flow chart methodology for performing low-voltage three-phase motor coordination studies -- NEMA design E motors and controls-what's it all about? -- Flammable vapor ignition initiated by hot rotor surfaces within an induction motor-reality or not? -- A comparative review of NEC versus IEC concepts and practices -- A tool for reliability and safety: predict and prevent equipment failures with thermography -- Electric re-regulation and effects on industrial customers -- Field motor testing: procedures which limit amount of involved risk -- The use of surge protection devices in the petroleum/petrochemical industry -- Heat tracing performance and reliability, the rest of the story -- Process safety management and the electrical function -- Cable or conduit-who uses it and why? -- Mechanical design of induction motors applied on adjustable speed drives -- The selection of motors in hazardous atmospheres and hostile environments. A theoretical and practical guide -- Monitoring partial discharges on 4 kV motor windings -- Pipelines, programmable logic controllers, and safety -- Fast tracking a 30.6 MW supersynchronous LCI compressor drive on a large gas transmission pipeline -- Control modernization of SCR rectifiers with continuous device current monitoring -- The process of conducting and communicating forensic analysis of electrical failures -- Specifying rectifiers for electrochemical |
|
|
|
|
|
|
|
|
|
|
applications -- Low-voltage motor starting on limited capacity electrical systems -- Training in the use of electrical heat tracing "a course outline" -- Understanding the NEMA motor-generator standards of section MG-1-1993, revision 3, three-phase induction motors -- Dust explosions in process plants -- The OSHA Hazard Communication Standard's impact on wire and cable -- Starting high inertia loads [induction motors] -- On line monitoring of partial discharges on stator windings of large rotating machines in the petrochemical environment -- Direct current field test for medium voltage cables: why can no one agree? -- Application of an electronic starter for a delayed coke process water jet cutting pump -- Retrofitting pipelines with induction motors -- 44 MW 4 pole motor selected for compressor drive -- Sparking electrical discharge and heating in synchronous and induction machines: Can it be controlled? -- Staged tests increase awareness of arc-flash hazards in electrical equipment -- Testing update on protective clothing and equipment for electric arc exposure -- Effective implementation of electrical safety regulations and standards -- Evaluating medium voltage cable splices and terminations. |
|
|
|
|
|
| |